LED lightbar 1240mm, orange+white, 10-30V, ECE R65

LED lightbar 1240mm, orange+white, 10-30V, ECE R65


Hobart
Product code: sre9-1240AW
485,90 Eur incl. VAT
In stock! (> 20 pcs) - Products in stock ordered up to 12PM are usually shipped the next working day!
Hobart
Product code: sre9-1240AW

LED light ramp suitable for all types of vehicles. It is designed for vehicles where special emphasis is placed on the warning effect.

The thinnest and lightest LED ramp on the market, the only one that combines 2 available colours in one ramp (2V1) - orange and white light.

Due to its small height, it is particularly suitable for modern aerodynamic cars where it does not cause excessive noise and increased fuel consumption.

The package includes a wired controller with mode switching and display of the selected mode.

The ramp has Class 2 approval, which means it can be switched to night mode (dimming of the light intensity), which can be switched manually or with the help of the built-in light sensor.

 

Advantages:

- 2in1 - 2 available colours in one ramp

- Versatile white light - allows for workplace illumination or routing

- light sensor - allows automatic brightness adjustment to ambient light conditions

- R65 Class 2 approval - the brightest light ramp on the market

- Intelligent driver - omnidirectional control with colour combination

- Driver routing function - left, right, centre

- easy to repair - using separately replaceable modules

- maximum water resistance - IP69K

- aluminium body with powerful cooling system

 

Technical parameters:

- supply voltage 10 - 30 V

- light source: 204 x 2W LED (orange), 228 x 0.5W LED ( white)

- 10 variants of warning flashing modes including routing

- ECE R65, Class 2, R10, CISPR 25 approval

- Dimensions: 1240 x 180 x 30 mm (height including bracket 67 mm)

- waterproof IP69K

- working temperature -45º - +65ºC

- screw mounting

- aluminium body + UV resistant PC cover

- Connection: 3m power cable terminated with loose wires (+ 3m cable with wired remote control for switching on + buttons for switching modes)

Color White, Orange
Certification CISPR 25 is an automotive EMC standard that specifies test methods and limits for conducted and radiated radio disturbances from vehicle components to protect on-board receivers. ECE R10 covers the approval of vehicles and electrical/electronic equipment with regard to electromagnetic compatibility (EMC). It sets requirements so in-vehicle devices limit electromagnetic emissions and have adequate immunity to interference. EHK R65 TA2 denotes a Category T (360°) beacon, A = amber, in Class 2 (two intensity levels including a reduced night mode).
Protection rating The product uses the automotive “K” test variant per ISO 20653: “6K” dust-tight under road-vehicle test conditions and “9K” high-pressure/hot water jet cleaning resistance.
Voltage 10-30V
Connection type Connection and control via an external control box. Enables switching modes, intensity or flash patterns depending on the device.
Mounting type Screw mount – a stable installation using screws (typically through a base plate or mounting holes). Best where the beacon is intended to stay permanently installed.
Length 1240 mm
Height 68 mm
Lightbar height without carriers 30 mm
Width 180 mm
Before using the device, carefully read the instructions and follow the warnings, safety information, and recommendations to prevent injury or damage. If possible, test the product and its functionality before installation. Perform the installation with the power disconnected and observe the correct polarity. Check the correct voltage (12/24 V) and use the appropriate fuse. Do not use damaged cables, connectors, or devices. Ensure that the cables are securely fastened and routed away from sharp edges and hot parts of the engine. The lights can be very intense and hot: do not look directly into the light source and do not touch it immediately after operation. Keep out of reach of children and protect from water unless the product is specifically designed for outdoor use. When using on public roads, familiarize yourself with and comply with local regulations. Use the product only for its intended purpose.
Manufacturer's representative in the EU STUALARM IMPORT, s.r.o
Address of representative in the EU Na Křivce 1082/30, 10100 Praha 10 - Vršovice
EU representative email info@stualarm.cz

Alternative products8

%s ...
%s
%image %title %code %s
%s